Bottom line, open up the instruction manual that comes with the box! Of course, if you somehow totally screwed it up, you can always clean everything up and try again. Once the heatsink is sitting on the processor with one fastener in each hole, hold it in place with one hand while pressing down firmly on each of the fastener 'legs' in turn. That means lifting the locking lever outwards and upwards completely to unlock the socket. For reference, the torque required for the nuts to fully tighten is 1. The steps for an upgrade are similar to that of installing but require that a processor is removed first by reversing the installation instructions.
This is an example of too much thermal compound. The Heat Sinks that come without thermal compound applied will have to have some applied to the top of the processor or the bottom of the heat sink. Ensure that the black top of each fastener is rotated into the correct locking orientation, with the arrow pointing away from the heatsink, and the groove in the top oriented towards the center of the heatsink as illustrated above. Filed under: Published: Author: External Mfg. Because, generally speaking, that one little cpu chip is simultaneously the smallest, most delicate, and most expensive part of your system. You simply lock your cooler down using whatever mechanism yours comes with and then move on. Do not remove the grease cover from a heat sink until you are instructed to do so.
It might appear as a triangular pattern. There will be more than one header on the motherboard, so be sure that you pick the right one. Turn each screw one-half a turn at a time. If the heatsink is not installed properly it might come loose. If you have decided on one of the closed loop coolers that are gaining popularity these days then you need to follow the instructions that come with the cooler for placement of the radiator.
Please refer to the documentation for the heat sink to ensure proper installation. Attention: To prevent damage to components, make sure that you follow the indicated tightening sequence. This orientation ensures the fastener will lock into place when pressed down. . Go ahead and read this article, as we uncover the right way to install this nifty computer accessory.
There are two ways to install the heat sink and it depends on what you get for a cooler, there are those that come with the thermal compound pre-applied. Expires in 90 days except where prohibited by law. Install the Heatsink Now we learn how to install a heatsink. The assembly usually has a 3-pin power connector. Tighten the screws until they stop; then, visually inspect to make sure that there is no gap between the screw shoulder beneath the heat sink and the microprocessor socket.
Excessive heatsink movement can cause the thermal compound to smear and become uneven. Ensure that the heatsink is sitting evenly on top of the socket and processor. Align the heat sink and fan assembly retainers with the holes on the motherboard. It is best to spread the paste evenly by covering your finger with a new clean plastic bag. Attach or Mount the Heatsink Clamp the heat sink in place using the proper mounting technique required by the solution. Note: When the processor is out of its retainer, hold the processor by the long edges to prevent touching the contacts or the thermal grease, if it is applied. If you feel comfortable doing it, you can use a very very slight rubbing motion as you press down on the cooler to help spread the paste better.
The compound spreads out evenly under the weight and pressure of the heat sink and fan assembly. There are several different types of thermal material, including ceramic- and metal-based pastes and solid, waxy thermal pads. Test the connections by powering up the computer. All processors on the system board must have the same speed, number of cores, and frequency. Using anti-static equipment, carefully lift the processor from its packaging and install it making sure to properly align processor and socket. Motherboards only support specific brands and types of processors. Just apply a drop or two to the old material and let it sit for a minute while the cleaner breaks up the grease in the thermal paste.
Tighten the screws until they stop; then, visually inspect to make sure that there is no gap between the screw shoulder beneath the heat sink and the processor socket. When applying thermal compound please follow the tutorial on applying and spreading thermal compound. There is no special way the heatsink has to face, as long as the point on the end of each of the 'legs' fits into one of the holes. Consult your motherboard manual if you are unsure of the location. Tighten the assembly retainers to secure the assembly in place. Contact your Microsoft representative for more information about Shape the Future.
If the heatsink didn't come with any thermal compound applied, add a small amount to the top of the Intel processor and spread it around evenly. For reference, the torque required for the nuts to fully tighten is 1. Applying too much thermal compound will cause an insulating effect and not allow the proper transfer of heat between the top of the processor and the bottom of the Heat Sink. Some heatsinks are installed by requiring you to clamp down on them with levers and attaching them to metal hooks on the motherboard. So the first order of business is to clean off the old thermal material.